Multi-Timeframe Screen Layout: A Three-Grid Design

Most multi-timeframe analysis is two charts on two tabs, switched between under pressure. A fixed three-grid layout puts the decision in one glance and removes the cost of rebuilding context every time you switch.

Multi-timeframe analysis fails not because the concept is wrong but because the layout is. Switching tabs reloads context and encourages each timeframe to be read in isolation. A fixed three-grid layout — same ratios, same indicators, same positions every session — turns the analysis into a single picture and the decision into a top-down flow.

The grid structure

Three charts stacked vertically, top to bottom:

• Grid 1 (top): higher timeframe (HTF) — direction and structure.
• Grid 2 (middle): trading timeframe (TTF) — setups and entries.
• Grid 3 (bottom): lower timeframe (LTF) — execution and stops.

Each grid occupies roughly one-third of screen height. Same width. Same zoom level in price-to-bar ratio. Same indicator stack on all three (consistency is the point).

The timeframe ratio

Use a fixed 1:4:16 ratio between the three grids:

• Swing trader: weekly / daily / 4-hour.
• Day trader: daily / 4-hour / 1-hour.
• Scalper: 4-hour / 1-hour / 15-minute.

Avoid 1:2:4 ratios — the timeframes overlap and produce false confirmation because the same price action appears on multiple grids. The 1:4 ratio ensures each higher grid holds approximately four bars of the grid below.

The indicator stack

Identical on all three grids, to allow direct comparison:

• 20 and 50 EMA: trend direction and slope.
• ATR(14) as an overlay label (not a sub-panel): risk reference.
• Volume with 30-bar average: effort reference.
• One oscillator (RSI 14): momentum alignment.

Do not add a second oscillator or sub-panel indicator. The consistency is what makes the three grids comparable; clutter destroys the comparison.

The top-down decision flow

Read the grids in order, top to bottom, and let each grid's verdict gate the next:

1. Grid 1 (HTF): is the trend up, down, or flat? Only take TTF setups in the HTF direction. If HTF is flat, only take range setups.
2. Grid 2 (TTF): is there a setup in the HTF direction? A pullback to the 20-EMA, a harmonic completion, a VSA signal. If no setup, stand aside.
3. Grid 3 (LTF): does the LTF confirm the TTF setup within four bars? A reversal bar on volume above its V30. If no confirmation, do not enter.

Each grid answers one question and gates the next. The decision is a three-step filter, not three independent reads.

The workspaces per style

Pre-build workspaces for each style and switch between them, not between timeframes within a workspace: swing (weekly/daily/4-hour), day (daily/4-hour/1-hour), scalp (4-hour/1-hour/15-minute). Mixing timeframes within one workspace breaks the ratio and produces meaningless confirmation.

The annotation convention

Annotate identically across grids: HTF gets horizontal lines for major support/resistance and trend labels; TTF gets Fibonacci retracements, supply/demand zones, harmonic pattern labels; LTF gets entry trigger arrows, stop and target levels only. Do not annotate the HTF with TTF-level detail — the grids lose their distinct roles and the comparison collapses.

Common errors

• Different indicators per grid: makes comparison impossible. The stack must be identical.
• HTF too close to TTF (e.g., 1-hour / 30-minute / 15-minute): false confirmation. Use the 1:4 ratio.
• Reading grids bottom-up: LTF-first reading biases the decision toward noise. Always read top-down.
• Adding a fourth grid: three is the limit. A fourth splits attention and produces analysis paralysis.

The layout is the system. Build it once, use it every session, and multi-timeframe analysis stops being a chore and becomes a glance.